Sherwin Williams U00150-2OZ Jet Glo Conventional Matterhorn White Touch Up Paint - 2oz Kit

Jet Glo Matterhorn White U00150 is a high-performance, multi-component polyester urethane, designed for exterior use on high performance general aviation, business jet, and commercial aircraft. Jet Glo® has outstanding high-gloss appearance, durability and Skydrol fluid resistance with Sherwin-Williams Aerospace primers.

Advantages:

Shelf Life is applicable only for materials stored in unopened and undamaged original factory filled containers.

Minimum Storage Temp: 40°F / 4°C
Maximum Storage Temp: 100°F / 37°C

U00150: 3 years
CM0578520: 2 years

Click here to download PDF version of Product Data Sheet.

Jet Glo should be applied to a surface that has been coated with an approved, properly prepared and applied Sherwin-Williams Aerospace primer system.

For best adhesion of trim colors to the cured urethane base coat, a thorough scuff sanding is recommended. Scuff sanding and cleaning will assure long-term durability and adhesion of the applied coating.

Mixing Instructions

Shake color component for 10-15 minutes before admixing.

Admix by Volume:

1 Part - Jet Glo Matterhorn White U00150
1 Part - Jet Glo Hardener CM0578520

Add the Hardener into the Color Component.

Admixed product should be allowed a 30-minute induction time for optimum application performance.

Reduce to desired application viscosity with approximately 10-15% thinner. For a three-coat application, use up to 1˝ to two times the amount of reducer. (i.e. if adding a quart, then add 11/2 to two quarts of thinner for a three coat shoot.)

It is recommended to filter strain admixed and reduced paint before placing material in containers for spraying.

CM0120975 Accelerator can be used for quick drying times on stripes, registration numbers, and logos. Maximum dosage should be 1/2 fluid ounce per admixed gallon (15 mL per admixed 3.8 Liter).

Application

This product can be applied using conventional air spray equipment, HVLP, Graco Pro 4500 air electrostatic, or Graco Pro 4500 air assisted airless electrostatic. Please consult your Sherwin-Williams representative for specific equipment settings.

1. Make sure pots, guns, and lines are purged and cleaned.
2. Mix thoroughly and filter strain before spray applying.
3. Spray atomizing pressure: 40-50 psi (2.75 -3.45 bar)
   Pot pressure: 8-12 psi (0.55 – 0.83 bar) using a 60’ fluid hose (3/8” diameter)
   Delivery Rate: 8-10 fluid oz (236-295 mL) per minute
4. Always air-blow and tack-wipe the surfaces to be painted. Assure that the aircraft is properly grounded for potential static buildup.
5. Best application results are obtained by applying as a twocoat procedure. First apply a medium wet coat, allow a 30-45 minute “tack-off” period, followed by a second full wet coat. A third coat may be necessary on larger areas or if buffing the clear is included in the detail process.
6. If the dry time between coats exceeds 24 hours, the surface should be thoroughly abraded.
7. Recommended film thickness is:
   Wet: 4–6 mils (15-23 microns)
   Dry: 2-3 mils (50-75 microns)

NOTE: Application of these product systems requires recommended temperature / humidity conditions and film thickness ranges. The material, hangar, and aircraft skin temperature should be no lower than 55°F / 13°C before, during, and after application.

Drying Schedule

Dry times are based on the dry film thickness of 2-3 mils (50-75 microns).

Air Dry Times (75°F / 25°C, 50% RH) To Tape: Unaccelerated - 16-18 Hours, Accelerated - 2-3 Hours
Recoat Time: Max. 24 Hours

NOTE: Lower temperatures, heavy film thickness, improper activator range selection and poor air movement will extend the dry time.

Equipment Cleanup

Use clean Ketone–type solvents such as CM0110308 MEK. Do not allow material to cure inside equipment.